Liv Garage Door Repairs & Service Blog

Garage Door Crooked on One Side: Worn Rollers, Bent Track, or a Tired Spring

November 19, 2026 6 min read
Torsion spring and drum assembly above a door

A garage door that sits crooked is one of the more common calls we get across Auburn, Kent, Federal Way, Renton, and the surrounding suburbs. You pull into the driveway and the door is down, but one corner is low. Or it is up, and the gap along the top is wider on one side than the other. Sometimes the door still opens and closes, just not evenly, and sometimes it stops partway and hangs at an angle. The important thing to understand up front is that a crooked door has several possible causes, and they are not interchangeable. A snapped cable, a broken spring, and a bent track all produce a door that hangs out of level, and each one calls for a different repair. This article covers what you can safely observe from outside the door, which causes are most likely, and what separates them.

What you can see without touching anything

With the garage empty and the door closed, stand back a few feet and look at the door as a whole. The most useful observations are simple ones: Is one side of the bottom edge sitting higher than the other? Is there a visible gap along the top of the door on one side? Does the door look like it is sitting square in the opening, or does one edge appear to be pulled away from the jamb? These are all things you can note from the driveway or from inside an empty garage without putting your hands on the hardware.

It also helps to note when the problem appeared. A door that was level last week and crooked today points to a sudden failure. A door that has drifted out of level over months or years points to wear. That distinction matters when a technician arrives, so write down what you noticed and when.

Cause one: a snapped cable

This is one of the few causes that is mechanically certain. A door with a snapped cable hangs at an angle. The cables run from the bottom corners of the door up to the drums at the top, and they keep the two sides of the door traveling together. When one cable lets go, that side of the door loses its lift and the door drops or hangs low on that corner. If you can see the door sitting noticeably crooked and it happened suddenly, a cable is a strong possibility.

Cables are under tension and are not a homeowner repair. Do not try to reattach, adjust, or handle a cable in any way. Keep the door where it is, keep people and vehicles clear of it, and call a technician.

Cause two: a broken torsion spring

A torsion spring that has snapped cannot hold the weight of the door. That is a certainty, not a guess. When one of a pair of springs breaks, the door often hangs crooked because the remaining spring is doing all the counterbalancing on one side. You may also notice the door feels heavier than usual in normal use, or that the opener runs but the door barely moves or does not move at all.

Springs are wound under high tension and are the most dangerous part of the door to work on. Do not touch them, do not try to wind or unwind them, and do not run the opener repeatedly to see if it will catch. Call a technician.

Cause three: worn rollers or a bent track

Not every crooked door is a sudden failure. On older builder-grade doors, especially in tract housing from the 1970s through the 2000s, the rollers and the track take a lot of wear. Rollers that have flat-spotted or lost their bearings can let one side of the door ride differently than the other. A track that has been bumped, or that has bent slightly over time, can pull one side of the door out of line. In this area, months of rain and constant damp also rust steel hinges and rollers, which accelerates that wear.

This is where a crooked door gets harder to diagnose from the driveway. A worn roller, a bent track, and a tired spring can all produce a door that does not sit level, and the test that separates them belongs to a technician, who checks the rollers, the track alignment, and the spring tension together. What you can do is note whether the door is noisy, whether it shudders as it moves, and whether the crookedness is constant or changes as the door travels.

What not to do

It is tempting to try to straighten a crooked door yourself, and it is worth being clear about why that is a bad idea. Do not pull the emergency release and try to move the door by hand. Do not try to lift the door to feel whether it is balanced. Do not adjust the track or the springs. All of that work involves stored energy and moving parts that can cause serious injury, and it belongs to a technician.

What you should do is stop running the opener. A door that is crooked and being driven by the opener can damage the panels, the track, and the opener itself. Leave the door where it is, keep vehicles and people clear, and call for service.

When to call

If the door is crooked, the safest next step is a technician visit. Liv Garage Door Repairs & Service handles residential and commercial garage door repair across Auburn and the surrounding areas, including spring replacement, cable repair, off-track and roller repair, and tune-ups. You can reach the team at (425) 386-7589 or info@livgaragedoors.com. The office is at 5548 34th St SE, Auburn, WA 98092, and weekday hours are Monday through Saturday, 7:00 AM to 8:00 PM, with Sunday emergency service only and 24/7 emergency dispatch.

A crooked door is rarely a mystery once someone who knows the hardware has looked at it. The value of calling early is that it keeps a small repair from becoming a larger one, and it keeps everyone in the household away from parts that are not safe to handle.

Need this looked at by a technician? Call Liv Garage Door Repairs & Service.

Call (425) 386-7589